295 lines
11 KiB
Markdown
295 lines
11 KiB
Markdown
# Temp. and Humidity Logger for the RPI4b
|
|
|
|
This is a simple temperature and humidity logger for a Raspberry Pi 4B running
|
|
FreeBSD 14. It is capable of taking temperature and humidity every 5
|
|
seconds and storing them into a database. The measurements can then be viewed
|
|
using either the integrated display, or, they can be exported to a USB drive.
|
|
|
|
# Goals
|
|
|
|
One of the most important goals for this project is that this device should be
|
|
low maintenance. Therefore, you should not have to connect it to a computer or
|
|
the network for years at a time. As this device has not yet been in service for
|
|
more than a few weeks, this cannot yet be guaranteed, however, it has been
|
|
designed to, at least in theory, be capable of this. It allows you to change the
|
|
device's time, date, and timezone from the built in display, as well as allowing
|
|
you to export data and clear the internal storage of collected data. Finally, it
|
|
should be able to survive a full drive, however, as there are a lot of
|
|
variables, it may not be able to.
|
|
|
|
# Contents
|
|
1. [Construction](#construction)
|
|
2. [OS Preparation](#os-preparation)
|
|
3. [Installation](#installation)
|
|
4. [Configuration](#configuration)
|
|
5. [Usage](#usage)
|
|
|
|
# Construction
|
|
The following is a general list of materials required:
|
|
|
|
- 1x Raspberry Pi 4 Model B [^1]
|
|
- 1x Breadboard (medium or large)
|
|
- 4x Push button
|
|
- 1x DHT11/DHT22 [^2]
|
|
- 1x DS3231 (or other RTC)
|
|
- 1x 16x2 HD44780U based LCD (such as a 1602 LCD, not I²C)
|
|
- 1x N-channel MOSFET (optional, for turning off the screen)
|
|
- 1x Schottky diode (optional, for turning off the screen)
|
|
- 1x 1kΩ resistor [^3]
|
|
- 2x 10kΩ potentiometers (optional, for display brightness and contrast control)
|
|
|
|
[^1]: Other versions and models will very likely work (such as the Pi 3B), the
|
|
wiring will just need to be adjusted.
|
|
|
|
[^2]: Any temperature and humidity sensor for which a FreeBSD kernel module
|
|
exists will work. You can even use separate sensors for each!
|
|
|
|
[^3]: If your DHT11/DHT22 is mounted on a carrier board with only three
|
|
terminals, it likely already has this resistor. When in doubt, check the
|
|
data sheet.
|
|
|
|
The following is one possible way to assemble the device. It should be noted,
|
|
however, that all of the pins are configurable. Thus, the following design
|
|
should be modified depending on the exact make and model of the parts being
|
|
used.
|
|
|
|
|
|
|
|
If an I²C device will be used (such as the DS3231 or an I²C sensor), care must
|
|
be taken that the data lines are connected to GPIO pins 2 and 3 (physical pins 3
|
|
and 5). If they are not, the configuration files provided in this repository
|
|
will need to be updated to reflect the new I²C bus location. If multiple I²C
|
|
devices are used, multiple busses will need to be created. For more information
|
|
about I²C on FreeBSD see the following man pages: [iic(4)][1], [iicbus(4)][2],
|
|
and [fdt(4)][3].
|
|
|
|
[1]: https://man.freebsd.org/cgi/man.cgi?query=iic&apropos=0&sektion=4&manpath=FreeBSD+14.0-RELEASE+and+Ports
|
|
[2]: https://man.freebsd.org/cgi/man.cgi?query=iicbus&apropos=0&sektion=4&manpath=FreeBSD+14.0-RELEASE+and+Ports
|
|
[3]: https://man.freebsd.org/cgi/man.cgi?query=fdt&apropos=0&sektion=4&manpath=FreeBSD+14.0-RELEASE+and+Ports
|
|
|
|
Some images of a fully assembled and working unit follow:
|
|
|
|
|
|
|
|
|
|
|
|
# OS Preparation
|
|
|
|
This software was designed and tested on a system running FreeBSD 14.0. However,
|
|
it should work on systems running FreeBSD 13 as well as on systems running
|
|
future versions of FreeBSD. The FreeBSD installation process is very well
|
|
documented in [The FreeBSD Handbook][4]. For convinience, the general procedure
|
|
is also provided below. If any issues arise or you have any questions, be
|
|
consult the handbook.
|
|
|
|
[4]: https://docs.freebsd.org/en/books/handbook/
|
|
|
|
First, download the latest image for the Raspberry Pi [here][5]. It is also a
|
|
good idea to pick up the checksum file. Once done you should have two files with
|
|
names similar to `FreeBSD-14.0-RELEASE-arm64-aarch64-RPI.img.xz` and
|
|
`CHECKSUM.SHA256-FreeBSD-14.0-RELEASE-arm64-aarch64-RPI`. To verify the
|
|
downloaded files, open a terminal and execute the following commands (use sha512
|
|
if you downloaded the sha512 checksum file):
|
|
|
|
[5]: https://www.freebsd.org/where/
|
|
|
|
- GNU/Linux and FreeBSD:
|
|
```sh
|
|
sha256sum -c CHECKSUM.SHA256-FreeBSD-14.0-RELEASE-arm64-aarch64-RPI
|
|
```
|
|
- OpenBSD:
|
|
```sh
|
|
sha256 -c CHECKSUM.SHA256-FreeBSD-14.0-RELEASE-arm64-aarch64-RPI
|
|
```
|
|
|
|
For other operating systems, please consult the relevant documentation.
|
|
|
|
Because device numbering is not persistent across boots, the export feature of
|
|
this software does not allow a specific device to be excluded from the
|
|
list. This may in the feature be rectified by an update, but for now, it is
|
|
recommend to install the OS to a microSD card. Most Raspberry Pis come with a
|
|
small USB device that can be used to write to microSD cards, as well as the
|
|
microSD card itself. If not, you can find both online very cheaply. Once you
|
|
have connected your device find it's device file using a tool like `fdisk` or
|
|
`geom`. Then execute the following commands as root to write the image to the
|
|
microSD card:
|
|
|
|
```sh
|
|
unxz FreeBSD-14.0-RELEASE-arm64-aarch64-RPI.img.xz
|
|
cp FreeBSD-14.0-RELEASE-arm64-aarch64-RPI.img /path/to/device
|
|
sync
|
|
```
|
|
|
|
If you are not comfortable with performing this operation on the terminal,
|
|
another option is to use software such as [balenaEtcher][6].
|
|
|
|
[6]: https://etcher.balena.io/
|
|
|
|
Once this process is done (which may take a while), insert the microSD card into
|
|
the Raspberry Pi, attach a keyboard and monitor, and plug the Pi in to turn it
|
|
on.
|
|
|
|
# Installation
|
|
|
|
Once the system has booted and you see the login prompt, enter `root` as the
|
|
username and leave the password blank. You should now see a shell prompt. The first
|
|
thing to do is to configure the temperature sensor and the RTC. To do the
|
|
former, *append* the following to the end of the `/boot/loader.conf` file:
|
|
|
|
```conf
|
|
# Load the DHT11/DHT22 kernel module
|
|
gpioths_load="YES"
|
|
# The GPIO bus that manages the pins that the sensor is connected to
|
|
hint.gpioths.0.at=gpiobus0
|
|
# This number should have only the bit set for the position corresponding to the
|
|
# GPIO pin number that the sensor is connected to. For example:
|
|
# 2097152 -> 1000000000000000000000 -> pin 21 (bit 22)
|
|
# 1 -> 1 -> pin 0 (bit 1)
|
|
# 2 -> 10 -> pin 1 (bit 2)
|
|
hint.gpioths.0.pins=2097152
|
|
|
|
# Load the DS3231 kernel module
|
|
ds3231_load="YES"
|
|
# The I2C bus the controls the pins the sensor is connected to
|
|
hint.ds3231.0.at=iicbus0
|
|
# The *8 BIT* address of the sensor. The following is the default for a DS3231
|
|
# addr = 0xd0
|
|
hint.ds3231.0.addr=208
|
|
```
|
|
|
|
The FreeBSD base system comes with the text editor `vi`. For information about
|
|
how to use it, execute `man vi` or see [vi(1)][7].
|
|
|
|
[7]: https://man.freebsd.org/cgi/man.cgi?query=vi&manpath=FreeBSD+14.0-RELEASE+and+Ports
|
|
|
|
The next step is to enable I²C for the DS3231. Once again, *append* the
|
|
following to the end of the `[all]` section of the `/boot/msdos/config.txt`
|
|
file:
|
|
|
|
```conf
|
|
# Set the initial state of pins GPIO 2 and 3. Change this if you use different pins.
|
|
gpio=2,3=a0
|
|
# Load the overlay for an the DS3231 I2C real-time clock
|
|
dtoverlay=i2c-rtc,ds3231
|
|
```
|
|
|
|
For example, the `/boot/msdos/config.txt` file on my Raspberry Pi 4B looks like
|
|
this:
|
|
|
|
```conf
|
|
[all]
|
|
arm_64bit=1
|
|
dtparam=audio=on,i2c_arm=on,spi=on
|
|
dtoverlay=mmc
|
|
dtoverlay=disable-bt
|
|
device_tree_address=0x4000
|
|
kernel=u-boot.bin
|
|
gpio=2,3=a0
|
|
dtoverlay=i2c-rtc,ds3231
|
|
|
|
[pi4]
|
|
hdmi_safe=1
|
|
armstub=armstub8-gic.bin
|
|
enable_uart=1
|
|
```
|
|
|
|
Then enable the `ntpd` and `ntpdate` services to sync with the RTC on boot and
|
|
periodically:
|
|
|
|
```sh
|
|
service ntpd enable
|
|
service ntpdate enable
|
|
```
|
|
|
|
If you want, you can also change the `root` password at this point:
|
|
|
|
```sh
|
|
passwd
|
|
```
|
|
|
|
After doing this, reboot the system. Once done, execute the following commands:
|
|
|
|
```sh
|
|
sysctl dev.ds3231.0.temperature dev.gpioths.0.temperature
|
|
```
|
|
|
|
If you get a warning about an unknown oid, it means that the sensor is not
|
|
installed or configured correctly.
|
|
|
|
It should be noted that FreeBSD does not currently support wireless on the
|
|
Raspberry Pi 4 at the time of writing. Thus, you will need to use a wired
|
|
connection (or consult the [handbook][4] for information about other ways to get
|
|
packages).
|
|
|
|
Once the sensors are detected and we have internet, we can install the
|
|
dependencies for this software. Execute the following command to bootstrap the
|
|
binary package manager [pkg(7)][8] and install sqlite3 and curl.
|
|
|
|
[8]: https://man.freebsd.org/cgi/man.cgi?query=pkg&manpath=FreeBSD+14.0-RELEASE+and+Ports
|
|
|
|
```sh
|
|
pkg install sqlite3 curl
|
|
```
|
|
|
|
When prompted to install `pkg`, type `y` and then press enter.
|
|
|
|
We can now download the source of this software:
|
|
|
|
```sh
|
|
cd /tmp
|
|
curl -O "https://git.zander.im/Zander671/rpi4b-temp-humidity/archive/main.tar.gz"
|
|
tar xf main.tar.gz
|
|
cd rpi4b-temp-humidity
|
|
```
|
|
|
|
At this point, take a moment to edit the `config.mk` file to to change any
|
|
default options. These can also be changed after installation by editing
|
|
`/usr/local/etc/rpi4b-temp-humidity/config.conf`.
|
|
|
|
Once you have configured everything to your liking, execute the following
|
|
command to build and install the software.
|
|
|
|
```sh
|
|
make install
|
|
```
|
|
|
|
# Configuration
|
|
|
|
The final step is to configure the software via the
|
|
`/usr/local/etc/rpi4b-temp-humidity/config.conf` file. Once you have done this
|
|
to your liking, execute the following command to enable the software on boot:
|
|
|
|
```sh
|
|
# Optional, set an alternate config file path
|
|
sysrc rpi4b_temp_humidity_config_file="/path/to/your/config/file"
|
|
service rpi4b-temp-humidity enable
|
|
```
|
|
|
|
The following command line flags are supported:
|
|
|
|
- `-h`: print a simple help message, then exit
|
|
- `-v`: enable more verbose output
|
|
- `-s`: exit immediately if an error is found in the config file
|
|
- `-f`: specify a different config file path
|
|
|
|
These can also be modified via the following [rc.conf(5)][9] variables (or via
|
|
the [sysrc(8)][10] command).
|
|
|
|
- `rpi4b_temp_humidity_config_file`: same as `-f`
|
|
- `rpi4b_temp_humidity_strict_config`: same as `-s`
|
|
- `rpi4b_temp_humidity_verbose`: same as `-v`
|
|
- `rpi4b_temp_humidity_log_file`: file to write output to, set to empty to
|
|
discard output
|
|
|
|
[9]: https://man.freebsd.org/cgi/man.cgi?query=rc.conf&manpath=FreeBSD+14.0-RELEASE+and+Ports
|
|
[10]: https://man.freebsd.org/cgi/man.cgi?query=sysrc&manpath=FreeBSD+14.0-RELEASE+and+Ports
|
|
|
|
# Usage
|
|
|
|
The buttons from closest to the display to farthest are: select, back, up, and
|
|
down. When the device first turns on, the stats screen will be shown. This screen
|
|
displays the current temperature, humidity, and time. Pressing the back button
|
|
will take you to the main menu. The following is a short description of each screen:
|
|
- "Stats by" screen shows stats by a specific period (e.g. hour, day, week)
|
|
-
|